จำหน่าย นำเข้า ขาย PEES Components - Servo Amplifier Pressure Controller Setpoint Module
HDC Test and commissioning unit for hydraulic drive systems
The WPG1 tester is used for actuation of proportional directional-control valves and also of non-position-controlled proportional throttle valves.
The WPG1 tester is used for actuation of proportional directional-control valves and also of non-position-controlled proportional throttle valves.
Servo Amplifier
The AN402 servo amplifier module is intended for the control of single magnet proportional valves. The control algorithm, ramps and similar command variables are derived exclusively from an external computer (PLC).
Servo Amplifier
The AN404 servo amplifier module is intended for the control of proportional valves with two magnets. The snap-on housing enables the AN404 module to be mounted on normal carrier rails in control cabinets. The electrical connections are via a terminal strip and a flat connector (enable input).
Servo Amplifier
The AN405 servo amplifier module is intended for the control of servo valves. It is available with various current ranges (±20mA, ±100mA, ± 200mA, ±300mA)
Pressure Controller
The AN410 pressure controller module is intended for pressure closed-loop-controls in conjunction with a pressure control valve. When the controller enable is switched off, the unit operates as an open loop controller in which the system pressure is adjusted in the usual manner by the valve current in conjunction with the control characteristic.
Setpoint Module
The AN417 setpoint module enables the universal input of setpoints for the control of servo and proportional valves. It has four setpoints and a polarity reverser.
Servo Amplifier
The AN418 servo amplifier module is intended for the control of proportional valves with two magnets. The snap-on housing enables the AN418 module to be mounted on normal carrier rails in control cabinets. The electrical connections are via a terminal strip and a flat connector (enable input).
Servo Amplifier
The AN419 servo amplifier module is intended for the control of single magnet roportional valves. The snap-on housing enables the AN419 module to be mounted on normal carrier rails in control cabinets. The electrical connections are via a terminal strip and a flat connector (enable input).
Servo Amplifier
The AN422 servo amplifier module is intended for the control of proportional valves with two magnets. The snap-on housing enables the AN422 module to be mounted on normal carrier rails in control cabinets. The electrical connections are via a terminal strip and a flat connector (enable input)
Servo Amplifier
The AN423 servo amplifier module is intended for the control of single magnet proportional valves. The snap-on housing enables the amplifier module to be mounted on normal carrier rails in control cabinets.
PID Controller Module
This PID controller module has been developed to meet the continuous demand for analog controller units in an easy-to-handle modular form.
Servo amplifier/PID Controller
The AN430 controller module has been developed, with the controller and servo amplifier accommodated in a single housing, for actuation of servo valves. The servo valve section can be supplied for four different current ranges (±20mA, ±100mA, ±200mA, ± 300mA).
The AN402 servo amplifier module is intended for the control of single magnet proportional valves. The control algorithm, ramps and similar command variables are derived exclusively from an external computer (PLC).
Servo Amplifier
The AN404 servo amplifier module is intended for the control of proportional valves with two magnets. The snap-on housing enables the AN404 module to be mounted on normal carrier rails in control cabinets. The electrical connections are via a terminal strip and a flat connector (enable input).
Servo Amplifier
The AN405 servo amplifier module is intended for the control of servo valves. It is available with various current ranges (±20mA, ±100mA, ± 200mA, ±300mA)
Pressure Controller
The AN410 pressure controller module is intended for pressure closed-loop-controls in conjunction with a pressure control valve. When the controller enable is switched off, the unit operates as an open loop controller in which the system pressure is adjusted in the usual manner by the valve current in conjunction with the control characteristic.
Setpoint Module
The AN417 setpoint module enables the universal input of setpoints for the control of servo and proportional valves. It has four setpoints and a polarity reverser.
Servo Amplifier
The AN418 servo amplifier module is intended for the control of proportional valves with two magnets. The snap-on housing enables the AN418 module to be mounted on normal carrier rails in control cabinets. The electrical connections are via a terminal strip and a flat connector (enable input).
Servo Amplifier
The AN419 servo amplifier module is intended for the control of single magnet roportional valves. The snap-on housing enables the AN419 module to be mounted on normal carrier rails in control cabinets. The electrical connections are via a terminal strip and a flat connector (enable input).
Servo Amplifier
The AN422 servo amplifier module is intended for the control of proportional valves with two magnets. The snap-on housing enables the AN422 module to be mounted on normal carrier rails in control cabinets. The electrical connections are via a terminal strip and a flat connector (enable input)
Servo Amplifier
The AN423 servo amplifier module is intended for the control of single magnet proportional valves. The snap-on housing enables the amplifier module to be mounted on normal carrier rails in control cabinets.
PID Controller Module
This PID controller module has been developed to meet the continuous demand for analog controller units in an easy-to-handle modular form.
Servo amplifier/PID Controller
The AN430 controller module has been developed, with the controller and servo amplifier accommodated in a single housing, for actuation of servo valves. The servo valve section can be supplied for four different current ranges (±20mA, ±100mA, ±200mA, ± 300mA).
The AN203 servo-amplifier has been designed for pressure control circuits with position-controlled pressure valves.
The AN206 controller module has been developed for use in plant engineering. Combination with other modular units permits assembly of any controller arrangements required. The P, I and D components can be adjusted internally or externally, via potentiometers.
The AN207PC servo-amplifier has been specially designed for pressure control circuits in conjunction with a pressure adjustment valve. Thanks to the use of a PI controller, this module permits high accuracy between the Actual pressure value and the target-value (setpoint) input.
The AN208 setpoint module was designed for the application of setpoints in electrohydraulic open and closed loop control systems. With this module, it is possible to connect external setpoint potentiometers or the setpoints that are adjustable on the module can be connected internally.
The AN209 servo amplifier has been designed to control single-magnet proportional valves and throttle-valves. The module is provided with various setpoint inputs: 4-20mA, 0-20mA, 0-5V, 0-10V, user selectable 10k /V An external enable input allows to lock the amplifier.
The AN 210 module has been designed as a logical element for systems. The many different OP circuits, solder tags for components and the possibility of external interconnection for the individual OP amplifiers make this module suitable for a wide range of applications.
The AN220 servo amplifier is suitable for controlling the most popular servo valves. The module provides current ranges of -20mA, -100mA, and -400mA for this purpose. The valve modulation can be adjusted by an internal/external limiter. In addition, the module is equipped with a PID controller, allowing a control system with a servo valve to be set up.
The AN 223 measurement socket module has 20 measurement sockets on the front plate. These allow rapid checking of the individual function stages of a system. In addition, 9 pairs of solder tags are provided for use as required.
The AN 230 was especially designed as a amplifier to control proportinal valves without position feedback combined with the possibility to get the command signals direct from the amplifier. Hereby the command signals can be used as fixed values or together with an external potentiometer.
The AN236 servo-amplifier has been specially developed for yoke positioning on an axial piston pump.
The amplifier AN237 was developed to control proportional valves in a closed-loop control.
The AN238 servo amplifier has been designed for the control of axial piston pumps valves in conjunction with servo valves. The module can be used as a pressure controller (zero stroke pump) or a volumetric flow controller by changing jumpers.
The AN239 setpoint module permits universal setpoint switching in electro-hydraulic open and closed loop control systems. It has five adjustable setpoints and a polarity reverser. An externally switchable and adjustable ramp is assigned to each setpoint.
The AN 240 converter module has been developed to convert current signals to voltages and voltage signals to currents. A large selection of current and voltage ranges can be set thanks to the extensive input circuitry and simple positioning of jumpers.
The power supply AN 241 is a powerpack unit,which allows to supply installations and systems with 24VDC. The output of the unit are two voltages + 15VDC and 15VDC to supply analogues units. Additional be a auxiliary voltage made available.
The AN527 servo amplifier has been designed for controlled proportional-stroke valves with two magnet coils.
The amplifier AN528 was developed to control proportional valves in a closed-loop control. The AN527 is used as a basic unit. By connecting a special module it is possible to drive the AN527 as the AN528 together with positioning controlled proportional valves.
The AN532 servo amplifier has been designed to control single-magnet proportional valves and throttle valves.
The AN533 servo amplifier has been designed to control single-magnet proportional valves and throttle valves with position controller.
The AN535 servo amplifier has been designed as a low-cost unit for single-magnet proportional valves.
The AN206 controller module has been developed for use in plant engineering. Combination with other modular units permits assembly of any controller arrangements required. The P, I and D components can be adjusted internally or externally, via potentiometers.
The AN207PC servo-amplifier has been specially designed for pressure control circuits in conjunction with a pressure adjustment valve. Thanks to the use of a PI controller, this module permits high accuracy between the Actual pressure value and the target-value (setpoint) input.
The AN208 setpoint module was designed for the application of setpoints in electrohydraulic open and closed loop control systems. With this module, it is possible to connect external setpoint potentiometers or the setpoints that are adjustable on the module can be connected internally.
The AN209 servo amplifier has been designed to control single-magnet proportional valves and throttle-valves. The module is provided with various setpoint inputs: 4-20mA, 0-20mA, 0-5V, 0-10V, user selectable 10k /V An external enable input allows to lock the amplifier.
The AN 210 module has been designed as a logical element for systems. The many different OP circuits, solder tags for components and the possibility of external interconnection for the individual OP amplifiers make this module suitable for a wide range of applications.
The AN220 servo amplifier is suitable for controlling the most popular servo valves. The module provides current ranges of -20mA, -100mA, and -400mA for this purpose. The valve modulation can be adjusted by an internal/external limiter. In addition, the module is equipped with a PID controller, allowing a control system with a servo valve to be set up.
The AN 223 measurement socket module has 20 measurement sockets on the front plate. These allow rapid checking of the individual function stages of a system. In addition, 9 pairs of solder tags are provided for use as required.
The AN 230 was especially designed as a amplifier to control proportinal valves without position feedback combined with the possibility to get the command signals direct from the amplifier. Hereby the command signals can be used as fixed values or together with an external potentiometer.
The AN236 servo-amplifier has been specially developed for yoke positioning on an axial piston pump.
The amplifier AN237 was developed to control proportional valves in a closed-loop control.
The AN238 servo amplifier has been designed for the control of axial piston pumps valves in conjunction with servo valves. The module can be used as a pressure controller (zero stroke pump) or a volumetric flow controller by changing jumpers.
The AN239 setpoint module permits universal setpoint switching in electro-hydraulic open and closed loop control systems. It has five adjustable setpoints and a polarity reverser. An externally switchable and adjustable ramp is assigned to each setpoint.
The AN 240 converter module has been developed to convert current signals to voltages and voltage signals to currents. A large selection of current and voltage ranges can be set thanks to the extensive input circuitry and simple positioning of jumpers.
The power supply AN 241 is a powerpack unit,which allows to supply installations and systems with 24VDC. The output of the unit are two voltages + 15VDC and 15VDC to supply analogues units. Additional be a auxiliary voltage made available.
The AN527 servo amplifier has been designed for controlled proportional-stroke valves with two magnet coils.
The amplifier AN528 was developed to control proportional valves in a closed-loop control. The AN527 is used as a basic unit. By connecting a special module it is possible to drive the AN527 as the AN528 together with positioning controlled proportional valves.
The AN532 servo amplifier has been designed to control single-magnet proportional valves and throttle valves.
The AN533 servo amplifier has been designed to control single-magnet proportional valves and throttle valves with position controller.
The AN535 servo amplifier has been designed as a low-cost unit for single-magnet proportional valves.
